Product Categories
DRACO FIX 100
Single component polymer-cement mortar
Fine fast setting polymer-cement mortar for leveling and smoothing of surfaces.
Purpose: Leveling and smoothing of horizontal and vertical, interior and exterior concrete surfaces. Preparation layer before waterproofing and decorative coatings, tile adhesives and other finishing layers.
Benefits: Extra smooth mortar covering holes smaller than 5 mm and easy to apply.
DRACO FIX 110
Hydraulic binder
Ultra-rapid hydraulic binder with special additives.
Purpose: Immediately blocking (up to 2 minutes) penetration of water into cracks, breaches and joints of concrete structures
Benefits: Easy application with binding for up to 2 minutes. Mechanically resistant binder.
DRACO FIX 120
Polymer - cementitiou mortar
Cementitious mortar for smoothing and protection of concrete.
Purpose: Smoothing and protection of concrete surfaces to increase longevity and durability. Reprofilation of superficial defects in concrete, nests and broken parts.
Benefits: Easy installation with resistance to sulfates and chemicals. It does not harm the environment.
DRACO FIX 125
Cementitiou mortar
Repair cementitious fiber reinforced mortar with low elasticity modulus for remediation and reinforcement of walls.
Purpose: Remediation and reinforcement of walls in restoration work in combination with glass fiber mesh. Used also as mortar for repairs and plastering.
Benefits: Waterproof and vapor-permeable product with the high bond strength and low modulus of elasticity. Easy and effective to apply.
DRACO FIX 130
Cementitiou mortar
Repair thixotropic cementitious mortar for reprofilation of concrete.
Purpose: Reprofilation and repair of damaged layers in concrete due to oxidization of steel reinforcement. Repair of corners of columns, beams and balconies and smoothing of surface defects. Suitable for manual and machine applications.
Benefits: Product of excellent workability and high thixotropy which is easy to apply. Excellent adhesion to new and old concrete substrates and reinforcing bars.
DRACO FIX 140
Polymer-cement mortar for structural repairs
Thixotropic fiber reinforced cementitious mortar for structural repair of concrete.
Purpose: Structural repairs of damaged reinforced concrete structures, manual or machine application, for structural reinforcements and buildings subject to dynamic loads.
Benefits: Easy installation with the possibility of application in layers up to 5 cm thick. It does not harm the environment.
DRACO FIX 143
Cementitiou mortar
Fast setting thixotropic fiber reinforced cementitious mortar for structural repair of concrete.
Purpose: Structural repairs of damaged reinforced concrete structures, manual or machine application, for structural reinforcements and buildings subject to dynamic loads.
Benefits: Product of excellent workability and high thixotropy which is easy to apply. Excellent adhesion to new and old concrete substrates and reinforcing bars.
DRACO FIX 145
Cementitiou mortar
Liquid and fiber-reinforced cement mortar with controlled shrinkage for structural concrete repair.
Purpose: Liquid mortar for columns and beams repair, for restoring concrete floors (industrial and road) and for grouting rigid joints between concrete elements.
Benefits: The product does not shrink, adheres well to iron and concrete and is easy to apply. It has excellent flow features.
DRACO FIX 190
Polymer-cement coating
One component corrosion inhibiting polymer-cement coating for protection of steel reinforcement.
Purpose: Protection of steel reinforcement in concrete structures and adhesion improver between the old concrete and concrete repair mortars.
DRACO FIX 800
Epoxy resin
Two-component thixotropic epoxy resin for repairs.
Purpose: Filling of cracks, sealing of pillars, foundations, beams and walls. Fine finishing of uneven concrete constructions.
Benefits: Stability of 100% solids with shrinkage after curing.
DRACO FIX 200
Mortar
Cementitious-lime vapor permeable fine plaster for smoothing in gray color.
Purpose: Finishing fine plaster for drying of walls made of brick, stone and other mineral materials that are under conditions of rising capillary dampness. For internal and external use. Applied after DRACO FIX 220.
DRACO FIX 220
Mortar
Cementitious-lime macroporous vapor-permeable mortar for drying of walls in gray color.
Purpose: Drying of walls made of brick, stone and other mineral materials that are under conditions of rising capillary dampness. For internal and external use.
DRACO FIX 300
Polyurethane injection resin catalyst
Polyurethane injection resin catalyst.
Purpose: For concrete structures subject to displacement. It stops the penetration of water in structures such as foundations, underground structures (garages), tunnels and underpasses, sewage systems, tanks, water mains and dams.
Benefits: It successfully seals cracks and cavities in concrete, especially in joints with easy installation. Deep penetration with minimal pressure due to low viscosity.
DRACO FIX 310
Polyurethane injection resin catalyst
Polyurethane injection resin catalyst.
Purpose: As a catalyst for the DRACO® FIX 300 polyurethane resin.
Benefits: The activation of the DRACO® FIX 300 polyurethane resin is controlled by different dosing.
DRACO FIX 500
Carbon fiber band
Carbon fiber band 300g/m².
Purpose: Reinforcement of reinforced concrete, masonry and wooden structures.
Benefits: A lightweight product that increases the load-bearing capacity and strength of structural elements with a minimally invasive procedure.
DRACO FIX 510
Carbon fiber mesh
Carbon fiber mesh 200 g/m².
Purpose: Reinforcement of reinforced concrete, masonry and wooden structures.
Benefits: Economic solution of low weight and high strength. It does not corrode.
DRACO FIX 520
Carbon fiber lamella
Carbon fiber lamella width from 5 cm up to 15 cm.
Purpose: Static strengthening of external parts of building structures, increase of load and bearing capacity, reduction of stress in reinforcement.
Benefits: The product increases the load-bearing capacity and strength of structural elements with a minimally invasive procedure.
DRACO FIX 525
Carbon fiber fabric
Carbon fiber fabric from 200 g//m² up to 600 g/m².
Benefits: Simple, flexible and economical reinforcement method. Applicable to all surfaces, even curved ones (pillars, columns, silos, chimneys). The product does not corrode.
DRACO FIX 535
Carbon fiber fabric
Carbon fiberr fabric 400 g/m².
Benefits: Simple, flexible and economical reinforcement method. Flexible applicability, even around curved pipe-like surfaces. The product does not corrode.
DRACO FIX 810
Epoxy mortar
Epoxy mortar for carbon fiber reinforcement systems.
Benefits: Solvent-free and high mechanical strength product. It hardens without sticking and is thixotropic (allows the application of thicker layers).
DRACO FIX 815
Epoxy adhesive and primer
Epoxy adhesive and primer for carbon fibers reinforcement systems.
Benefits: Solvent-free and high mechanical strength product. It hardens without sticking and is thixotropic (allows the application of thicker layers).
DRACO FIX 820
Epoxy adhesive
Epoxy adhesive for carbon fiber reinforcement systems.
Benefits: Product of high strength adhesion and bond to the substrate. It hardens without shrinkage and is thixotropic (allows the application of thicker layers).
DRACO BOND 120
Cementitious adhesive
Improved cementitious adhesive for ceramic tiles in gray color.
Purpose: Bonding ceramic tiles on cement surfaces. Suitable for underfloor heating. For application "tile over tile", for balconies, terraces, bathrooms and swimming pools. For application on horizontal and vertical indoor and outdoor surfaces and above polymer cement waterproofing coatings.
Benefits: Easy to apply with a processing time of 2.5-3 hours. Excellent adhesion to various substrates (concrete, stone, brick). The product does not slide on vertical surfaces.
DRACO BOND 150
Cementitious adhesive
Improved cementitious adhesive for large format ceramic tiles in grey color.
Purpose: Bonding ceramic tiles on cement surfaces. Suitable for underfloor heating. For application "tile over tile", for balconies, terraces, bathrooms and swimming pools. For application on horizontal and vertical indoor and outdoor surfaces and above polymer cement waterproofing coatings.
Benefits: Easy to apply with excellent adhesion to most substrates (concrete, stone, brick, plaster). The product does not slide on vertical surfaces.
DRACO BOND 155
Cementitious adhesive
Improved cementitious adhesive for large format ceramic tiles, thicker layer application in grey color.
Purpose: Bonding ceramic tiles on cement surfaces. Suitable for underfloor heating. For application "tile over tile", for balconies, terraces, bathrooms and swimming pools. For application on horizontal and vertical indoor and outdoor surfaces and above polymer cement waterproofing coatings.
Benefits: Easy to apply with excellent adhesion to most substrates (concrete, stone, brick, plaster). The product does not slide on vertical surfaces.
DRACO GROUT 150
Grout for ceramic tile joints
High performance cementitious grout for ceramic tile joints, 0-4 mm.
Purpose: Filling of horizontal and vertical joints between ceramic tiles, natural stone, marble and glass mosaic.For internal and external use. Suitable for floor heating and wet areas.
Benefits: Waterproof mass of excellent resistance to abrasion, scratches and the formation of mold. Easy to clean and maintain. UV stable, extremely durable and resistant to freezing and thawing cycles.
DRACO GROUT 155
Grout for ceramic tile joints
High-performance cementitious grout for ceramic tile joints, 2-15 mm.
Purpose: Filling of horizontal and vertical joints between ceramic tiles, natural stone, marble and glass mosaic. For internal and external use. Suitable for floor heating and wet areas.
Benefits: Waterproof mass of excellent resistance to abrasion, scratches and the formation of mold. Easy to clean and maintain. UV stable, extremely durable and resistant to freezing and thawing cycles.
Join the DRACO family
Receive all the latest news related to our special offers, products, innovations and industry trends straight to your inbox.